 |
|
|
|
From the pages of Fine Woodworking Magazine A Simple Way to Upholster Chairs Slim, comfortable slip seat works for most chairs and uses common materials
My slip seat consists of three different densities of foam on a thin plywood platform (see Seat anatomy), which is slotted to allow it to flex and conform to the person using the chair. Cut slots in the seat platform I use 1/4-in.-thick plywood for the seat platform of dining chairs, while larger chairs that are designed to be used in a living room may have 1/2-in.-thick platforms. I always use Baltic-birch plywood for seat platforms because it has more laminations than other plywoods and the core is free of voids and quite strong.  The seat platform starts with 1/4-in.-thick Baltic-birch plywood and can be adapted to fit many types of chairs and seat configurations, from versions that overlay the seat frame to platforms that are inset into the seat frame.
For an inset slip seat like the one shown here, the platform should come up 1/8 in. short all around the inside of the seat frame. Foam and fabric added later will fill the gap. Build up the foam layers Moving from bottom to top, the foam layers go from high- to low-density (firm to soft). The closed-cell, high-density styrene foam used as the base layer of the seat is sold as sleeping-pad material for camping. It is available at camping-supply stores in thicknesses ranging from 1/4 in. to 3/4 in. To attach and laminate the foam pieces, I use spray adhesive, following the directions on the can for a permanent bond. Put down a base layer of dense foam -- Start the upholstery sequence by determining how thick (and comfortable) you want the final upholstered platform to be, then choosing the appropriate thicknesses of foam to get you there. For a dining chair, a final thickness of 1 in. to 1-1/4 in. is appropriate, so I start by attaching a layer of 1/4-in.-thick high-density styrene foam to the plywood platform. (The fractional sizes given here are approximate, because the materials I buy in Canada come in metric sizes.) Thicker seats can be made simply by increasing the thickness of this base layer and building up the outer band of firm foam that follows.
Add an outer band of high-density foam -- To avoid the rounded, muffin-top look, the next step creates a firm dam around the perimeter of the seat. This is done by attaching a band of high-density foam, about 1/2 in. thick by roughly 1-1/2 in. wide. If you are unable to find 1/2-in.-thick material, you can build up layers of thinner material. It is important to bevel the inside edge of this outer band to ease the transition between the high-density styrene foam and the medium-density urethane foam that will fill the center. Without the bevel, the change in firmness will be too abrupt.
Fill the center with urethane foam -- The next step involves filling the center with medium-density urethane foam. I get low- and medium-density urethane foam from a local fabric store. For the center section, use urethane foam that is slightly thicker than the dense foam used for the outer band. For a perimeter thickness of 1/2 in., for example, I recommend that the urethane foam be 5/8 in. thick. Cut the foam about 3/8 in. bigger than the opening all the way around and leave the edge square -- not at a 45° bevel. Spray adhesive on one side of the urethane foam and on its edges. Then spray the center surface of the seat, including the 45° edge but not the remaining top surface. Attach the square-cut edges of the urethane foam to the 45° edges of the band, working in from the corners. The center of the urethane foam will form a bubble. Press down the bubble into the center area in a uniform manner. There may be small bumps around the edges, but these will be evened out in the next step.
Add one last layer -- The next step is to wrap the surface in 1/4-in.-thick, low-density urethane foam. Lay the seat platform upside down on a piece of thin urethane foam cut about 2 in. larger all around. Spray the exposed 2-in. band of foam and the edges of the platform, and then lift the foam so that it bonds to the edges, avoiding large wrinkles at the corners. Lay a knife flat on the plywood and trim the excess foam flush to the surface.
Cover the platform The seat platform should be wrapped with thin, neutral-colored cotton muslin in preparation for the upholstery fabric. The cotton muslin can be stretched lightly with medium effort and stapled to the underside of the platform, followed by the upholstery fabric. A good hand stapler will work, but an air-powered stapler that shoots narrow staples is much easier to use, particularly if you intend to make a lot of upholstered chairs. I use a Haubold stapler with 1/4-in.-long wire staples, which tend to drive in completely, holding the fabric firmly.
Care has to be taken to read the upholstery fabric. There may be a pattern that should be kept centered or stripes that should be kept straight. If the fabric has a nap, it should point toward the back of the chair so that the person using the chair is less inclined to slide out. Use only upholstery fabric to cover a slip seat. Fabric made for clothing or drapery will become threadbare quickly. The fabric is attached in much the same way that an artist's canvas is stretched onto a frame: Start in the middle, stretching the fabric front to back, and tack down just the center of the front and back edges. Then stretch the fabric side to side and tack down the middle of the side edges. Now work toward the corners, adding a few staples at a time as you move outward. The tension used to stretch the fabric should be equal on all sides. When you reach the corners, pull the fabric around tightly, trying to avoid overlaps and wrinkles. Finish off this upholstery job by covering the bottom of the platform with black polyester cloth.
Options for installing the seat The slip seat can be supported in a number of ways, depending on the application. Most of my chairs have slip seats that are fully or at least partially set into the seat frame. To support these, I glue a plywood ring into the seat frame. It serves two purposes: supporting the seat platform and strengthening the seat frame. Like the seat platform, the thickness of the plywood seat ring is determined by the overall size of the chair. As the seat frame is assembled, the ring is set into a deep groove about 5¼8 in. below the top edge. Then the upholstered platform is squeezed into the space above the ring, hiding the edges of the platform. An alternative to insetting a slip seat into a seat frame is to let the upholstered platform hang over the front rail of the seat frame. In this case I usually attach a curved wood lip under the front edge of the platform, strengthening it and creating a plush look. If the slip seat must overlay the seat frame, it can be attached to wood blocks that are glued inside the frame. To attach the seat platform to the wood blocks or plywood ring, you must locate the attachment holes. I cut pieces of 1/4-20 threaded rod about 3/4 in. long and sharpen one end of each by filing it. To mark the location of the platform T-nuts, I thread the sharp bolts into the T-nuts and press down the upholstered platform into position. Then I drill the clearance holes in the seat ring and attach the slip seat with round-head machine screws. The result is a smooth, seamless, low-profile seat that will remain comfortable for many years.
|
|
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
